Refer to the exhibit. The Layer 2 network uses VTP to manage its VLAN database. A network designer created all VLANs on the VTP server （switch 1） and it has been advertised through VTP to all other VTP clients （switches 2 through 4）. Due to network growth， a network operator decided to add a new switch between switch 1 and switch 3. The network operator has been instructed to use a refurbished switch and use a VTP client. Which three of these factors should the network operator consider to minimize the impact of adding a new switch？（）
A. Pay special attention to the VTP revision number， because the higher value takes the priority.
B. Configure all VLANs manually on the new switch in order to avoid connectivity issues.
C. A trunk should be established between the new switch and switches 1 and 3 as VTP only runs over trunk links.
D. Set at least the VTP domain name and password to get the new switch synchronized.
E. An ISL trunk should be established between the new switch and switches 1 and 3， because VTP only runs over ISL.
F. Pay special attention to the VTP revision number， because the lower value takes the priority.
您可能感興趣的試卷
你可能感興趣的試題
A.It is used in multihome network scenarios.
B.It can be used with BGP to mitigate DoS and DDoS.
C.It does not need to have CEF enabled.
D.It is enabled via the interface level command ip verify unicast reverse-path.
E.It cannot be used with "classification" access lists.
A.Do not enable all the signatures at the same time.
B.Do not enable the ICMP signature.
C.Disable the Zone-Based Policy Firewall because it is not compatible with Cisco IOS IPS.
D.Disable CEF because it is not compatible with Cisco IOS IPS. .
A.It is a Cisco proprietary protocol.
B.It runs on TCP port 59. .
C.Authentication and authorization are done at different stages.
D.TACACS+ encrypts the entire body of the packet， but leaves a standard TACACS+ header.
E.It is an industry standard protocol.
F.TACACS+ encrypts both the entire body of the packet and the TACACS+ header.
A.it is used for load balancing in bidirectional PIM
B.it is used for redundancy in bidirectional PIM
C.it is used for redundancy in PIM-SM
D.it is used for load balancing in PIM-SM
Refer to the exhibit. Look at the command output. What can you use to prevent this behavior？ （）
A. UDLD （UniDirectional Link Detection）
B. spanning-tree loopguard
C. VTP mode transparent
D. switchport mode desirable
最新試題
Which two statements are true about RED？（）
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
What is also called Type 0 authentication in OSPF on Cisco Routers？（）
What is the correct command to set the router ID for an OSPFv3 process？（）
Choose two commands that are required to enable multicast on a router， when it is known that thereceivers use a specific functionality of IGMPv3.（）
In GLBP，which router will answer on client ARP requests？（）
Which three options are valid ways to filter routes from a BGP peer？（）
All of these are fundamental building blocks of differentiated services Traffic Conditioner Block exceptwhich one？（）
An expanding company is deploying leased lines between its main site and two remote sites. Thebandwidth of the leased lines is 128kb/s each，terminated on different serial interfaces on the main router.These links are used for combined VOIP and data traffic. The network administrator has implemented a VOIP solution to reduce costs，and has therefore reserved sufficient bandwidth in a low latency queue oneach interface for the VOIP traffic. Users now complain about bad voice quality although no drops areobserved in the low latency queue. What action will likely fix this problem？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）