After configuring FabricPath， the following appears in the syslog：
%STP-2-L2GW_BACKBONE_BLOCK： L2 Gateway Backbone port inconsistency blocking port port-channel100 on VLAN0010.
What is the cause of this message？ （）
A. STP must be disabled； message indicates that STP is enabled.
B. STP is misconfigured； root guard must be disabled.
C. An inferior BPDU is received on a Cisco FabricPath edge port.
D. A superior BPDU is received on a Cisco FabricPath edge port.
您可能感興趣的試卷
你可能感興趣的試題
A. short-text-destination
B. prerecorded audio alerts
C. CiscoTAC-1
D. dial911
E. full-text-destination
A. FabricPath switch ID must be configured under the vPC domain.
B. Virtual switch ID of vPC+ must be configured under FabricPath domain.
C. On Cisco Nexus 7000 Series Switch， F1 interfaces must be used as the vPC+ peer links.
D. The vPC+ peer link must be configured as a Cisco FabricPath core port （switchport mode fabricpath）.
E. FabricPath subswitch ID must be configured under the vPC domain.
A. encryption—scrambles the packet contents to prevent them from being seen by unauthorized sources
B. password—a password （community string） sent in clear text between a manager and agent for added protection
C. authentication—determines that the message is from a valid source
D. message integrity—ensures that a packet has not been tampered with while it was in transit
E. user—to determine if user authentication is used instead of community strings
A. Join interface is a Layer 3 entity， and with the Cisco NX-OS release 6.0， it can only be defined as a physical interface， physical subinterface， Layer 3 port channel， or Layer 3 port channel subinterface.
B. A single join interface can be defined and associated with a given OTV overlay.
C. Multiple overlays can also share the same join interface.
D. Join interface can be a loopback interface.
E. The join interface is a Layer 3 entity that can be defined as a physical interface but not as a logical one.
The network administrator is seeing N7K-1 having issues with VLAN 11， and interface VLAN 11 is resetting， causing frequent HSRP state changes. Which two actions would reduce HSRP state changes？ （）
A..On N7K-1，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
B..On N7K-2，configure the HSRP extended hold timer to 180， extending the HSRP hello message hold time.
C..On N7K-1，configure the pre-empt delay minimum to 180 in order to delay N7K-1 from taking over as the HSRP active router.
D..On N7K-2，configure the pre-empt delay minimum to 180 in order to delay N7K-2 from taking over as the HSRP active router.
E..On N7K-2，increase the HSRP priority to 150.
F. On N7K-2，decrease the HSRP priority to 50.
最新試題
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）