A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
您可能感興趣的試卷
你可能感興趣的試題
The network administrator is adding a new N1Kv to the vCenter， however， the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot：
VSM# show svs connections
connection VC：
ip address： 10.10.10.30
remote port： 80
protocol： vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status： Disabled
operational status： Disconnected sync status： -
version： -
When attempting to fix the issue， the following error is seen：
VSM-PRI-188# conf
VSM-PRI-188（config）# svs connection VC
VSM-PRI-188（config-svs-conn）# connect
ERROR： [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error？（）
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration：
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967，4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue？（）
A. Remove second NIC from each port profile
B. Remove VEM from VSM （no vem X）， remove NICs， and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
A. Send monitored traffic to a VLAN
B. Send monitored traffic to a remote VEM over L2
C. Receive monitored traffic on a vEthernet interface
D. Send monitored traffic to an IP destination
A. Source and destination interface must be on the same host
B. Source and destination interfaces can be on different hosts
C. Destination vEthernet interface can be on a different VLAN than the source
D. Destination interface can be a physical port
E. Destination interface cannot be a physical port
Given a host with two NICs assigned to a N1k profile，which topologies are suitable for this type of configuration （）
port-profile type Ethernet name VM-Data
vmware port-group
switchport mode trunk
switchport allowed vlan 400-410
channel-group auto mode active
no shut
state enabled
A. Cisco UCS fabric interconnects
B. Pair of N5K’s in VPC
C. Standalone N5K
D. Pair of N5K’s in non-VPC
E. Cisco Catalyst 6000 Switch in VSS
最新試題
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
Which of the following are supported in Cisco Global Site Selector？ （）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
What interface is created when an FC Port Channel is created on a Cisco Unified Computing System？（）