A. Cisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXes
B. Cisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXes
C. Two Cisco UCS 6100 Series or 6200 Series fabric interconnects
D. Two RJ45 Ethernet cables
E. The fabric interconnects must be in end-host mode
您可能感興趣的試卷
你可能感興趣的試題
A. Uplink Ethernet ports or border ports
B. Appliance ports
C. Server ports
D. Fabric ports
E. Backplane ports
F. vEth interfaces
G. A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.
A. FabricSync is used to synchronize MAC addresses to an adjacent fabric interconnect after a server interface failover.
B. Gratuitous ARPs are sent on fabric interconnect uplinks after a server interface failover.
C. Fabric failover can be used on vNICs and vHBAs.
D. Fabric failover is configured as part of the service profile.
E. Fabric interconnects in end-host mode use fabric failover instead of spanning tree to provide redundancy on uplink ports.
A. Interface inbound-low handles Rx and Tx of low-priority control packet
B. Interface inbound-lo handles Rx and Tx of high-priority control packet
C. Interface inbound-low maps to internal interface eth3
D. Interface inbound-low maps to internal interface eth4
A. The fabric interconnect is in the end-host mode， and all uplink ports have failed.
B. The server port to which the adapter is pinned has failed.
C. A transient error has caused the link to fail.
D. The fabric interconnect is in the switch mode， and all uplink ports have failed.
E. The link for a network-facing host interface is missing.
What would be the cause for the following fault in UCS Manager？（）
"ether VIF x / xxx down， reason： ENM source pinning failed"
A. The associated VLANs of a vNIC are not found on an uplink.
B. Overlapping VLAN IDs exist on upstream disjoint networks.
C. The vNIC was not configured for fabric failover.
D. The vNIC is pinned to the wrong fabric.
E. Overlapping VSAN IDs exist on upstream SAN switches.
F. The vHBA was not configured for failover.
最新試題
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
What is the use of an "all configuration" backup in Cisco UCS？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
In a Cisco Unified Computing System， where are SAN port channels connected to？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
Which are valid statements about Cisco Virtual Interface Card （VIC）？ （）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
An administrator is creating a service profile but receives an error when applying to a blade. The administrator checks the faults tab of the service profile and finds the following error （Refer to the exhibit）.What is the cause of this error？（）