Switch R1 is configured with VTP.
Which two VTP modes will make R1 capable of creating and deleting VLANs on itself？ （）
A. Client
B. Server
C. Transparent
D. Pass-through
E. No-negotiate
您可能感興趣的試卷
你可能感興趣的試題
What action should you execute if you wanted to enable VTP pruning on your entire management domain？（）
A. Enable VTP pruning on any client switch in the management domain.
B. Enable VTP pruning on any switch in the management domain.
C. Enable VTP pruning on every switch in the management domain.
D. Enable VTP pruning on a VTP server in the management domain.
E. Disable VTP pruning on a VTP server in the management domain.
A.It does not prune traffic from VLANs that are pruning-ineligible
B.VLAN 1 is always pruning-eligible
C.It will prune traffic from VLANs that are pruning-ineligible
D.VLAN 2 is always pruning-ineligible
E.None of the other alternatives apply
A.Domain advertisements
B.Advertisement requests from clients
C.Subset advertisements
D.Summary advertisements
A.The VLAN ID of all known VLANs，the management domain name，and the total number of trunk links on the switch.
B.The VLAN ID of all known VLANs，a 1-bit canonical format （CF1 Indicator），and the switch configuration revision number.
C.The management domain name，the switch configuration revision number，the known VLANs， and their specific parameters.
D.A 2-byte TPID with a fixed value of 0x8100 for the management domain number，the switch configuration revision number，the known VLANs，and their specific parameters.
E.None of the other alternatives apply.
A.A number for identifying changes to the network switch.
B.A number for identifying changes to the network router.
C.A number for identifying changes to the network topology.
D.None of the other alternatives apply.
最新試題
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）