Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them.
What will be the result？（）
A. IEEE 802.1D and IEEE 802.1w are incompatible. All three switches must use the same standard or no traffic will pass between any of the switches.
B. Switches S1， S2， and S3 will be able to pass traffic between themselves.
C. Switches S1， S2， and S3 will be able to pass traffic between themselves. However， if there is a topology change， Switch S2 will not receive notification of the change.
D. Switches S1 and S3 will be able to exchange traffic but neither will be able to exchange traffic with Switch S2
您可能感興趣的試卷
你可能感興趣的試題
The network administrator maps VLAN 10 through 20 to MST instance 2.
How will this information be propagated to all appropriate switches？（）
A. Information will be carried in the RSTP BPDUs.
B. It will be propagated in VTP updates.
C. Information stored in the Forwarding Information Base and the switch will reply on query.
D. Multiple Spanning Tree must be manually configured on the appropriate switches.
Refer to the show spanning-tree mst configuration output shown in the exhibit.
What should be changed in the configuration of the switch SW_2 in order for it to participate in the same MST region？ （）
A. Switch SW_2 must be configured with an instance number of 2.
B. Switch SW_2 must be configured with a different VLAN range.
C. Switch SW_2 must be configured with the revision number of 1.
D. Switch SW_2 must be configured with a different MST name.
While logged into a Company switch you issue the following command：
CompanySwitch（config-mst）# instance 10 vlan 11-12
What does this command accomplish？（）
A. It enables a PVST+ instance of 10 for vlan 11 and vlan 12
B. It enables vlan 11 and vlan 12 to be part of the MST region 10
C. It maps vlan 11 and vlan 12 to the MST instance of 10.
D. It creates an Internal Spanning Tree （IST） instance of 10 for vlan 11 and vlan 12
E. It create a Common Spanning Tree （CST） instance of 10 for vlan 11 and vlan 12
F. It starts two instances of MST， one instance for vlan 11 and another instance for vlan 12.
Which MST configuration statement is correct？ （）
A. MST configurations can be propagated to other switches using VTP.
B. After MST is configured on a Switch， PVST+ operations will also be enabled by default.
C. MST configurations must be manually configured on each switch within the MST region.
D. MST configurations only need to be manually configured on the Root Bridge.
E. MST configurations are entered using the VLAN Database mode on Cisco Catalyst switches.
A. MST00
B. MST01
C. the last MST instance configured
D. none
最新試題
Which three statements about STP timers are true？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which statement is correct about RSTP port roles？（）