Refer to the exhibit. EIGRP is configured with the default configuration on all routers. Auto summariz ation is enabled on routers R2 and R3, but it is disabled on router R1.
Which two EIGRP routes will be seen in the routing table of router R3?（）
A. 10.0.0.0/8
B. 172.16.10.0/24
C. 172.16.0.0/24
D. 10.10.10.0/24
E. 172.16.0.0/16
F. 10.10.0.0/16
您可能感興趣的試卷
你可能感興趣的試題
Based on the exhibited output, which three statements are true?（）
A. All the routes are in the passive mode because R1 is in the query process for those routes.
B. R1 is in AS 200.
C. R1 will load balance between three pat hs to reach the 192.168.1.48/28 prefix because all three paths have the same advertised distance (AD) of 40512000.
D. 40512000 is the advertised distance (AD) via 192.168.1.66 to reach the 192.168.1.48/28 prefix.
E. All the routes are in the passive mod e because these routes are in the hold- down state.
F. The best path for R1 to reach the 192.168.1.48/28 prefix is via 192.168.1.66.
A. A hub router prevents routes from being advertised to the remote router.
B. Only remote routers are configured as stubs.
C. Stub routers are not queried for routes.
D. Spoke routers connected to hub routers answer the route queries for the stub router.
E. A stub router should have only EIGRP hub routers as neighbors.
F. EIGRP stub routing should be used on hub routers only.
A. An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.
B. An EIGRP route will go passive if there are no successors in the EIGRP topology table.
C. DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.
D. A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.
E. The stuck in active state is caused when the wait for the query replies have timed out.
F. EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.
A. When summarization is configured, the router will also create a route to null 0.
B. The summary route remains in the route table, even if there are no more specific routes to the network.
C. Summarization is configured on a per- interface level.
D. The maximum metric for the specific routes is used as the metric for the summary route.
E. Automatic summarization across major network boundaries is enabled by default.
A. debug eigrp packets
B. show ip eigrp traffic
C. debug ip eigrp
D. show ip eigrp interfaces
最新試題
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable