A.The configuration of EIGRP offset lists
B.Current link loads
C.Changing interface delay settings
D.Configu ration of variance
您可能感興趣的試卷
你可能感興趣的試題
Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.
Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）
A.R1 limi ts EIGRP to around 250Kbps on DLCI 102
B.R1 limits EIGRP to around 250Kbps on DLCI 104
C.R1 limits EIGRP to around 150Kbps on every DLCI
D.R1 does not limit EIGRP because noWAN bandwidth control has been configured
A.Jitter
B.Delay
C.MTU
D.Reliability
A.By adding all subnets listed by the show ip route connected command
B.By adding the subnets of working interfaces over which static neighbors have been defined
C.By adding subnets redistributed on the local router from another routing source
D.By adding all subnets listed by the show ip route static command
An engineer has added the following configuration snippet to an implementation planning document. The configuration will be added to Router R1, whose Fa0/0 interface connects to a LAN to which Routers R2 and R3 also connect. R2 and R3 are already EIGRP neighbors with each of her. Assuming the snippet shows all commands on R1 related to EIGRP authentication, which answer lists an appropriate comment to be made during the implementation plan peer review?（）
key chain fred
key 3
key - string whehew
interface fa0/0
ip authenticat ion key - chain eigrp 9 fred
A.The configuration is missing one authentication - related configuration command
B.The configuration is missing two authentication - related configuration commands
C.Authentication type 9 is not supported; type 5 should be u sed insteaD
D.The key numbers must begin with key 1, so change the key 3 command to key 1
最新試題
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable