A hacker on the Company network is attempting to hop onto a different VLAN.
Which two statements about VLAN hopping are true？ （）
A. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
B. Configuring an interface with the "switchport mode dynamic" command will prevent VLAN hopping.
C. Attacks are prevented by utilizing the port-security feature.
D. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
E. An end station attempts to redirect VLAN traffic by broadcasting multiple ARP requests.
您可能感興趣的試卷
你可能感興趣的試題
The Company security administrator wants to prevent VLAN hopping on the network.
What is one method that can be used to do this？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
The Company security administrator is concerned with VLAN hopping based attacks.
Which two statements about these attacks are true？ （）
A. Attacks are prevented by utilizing the port-security feature.
B. An end station attempts to gain access to all VLANs by transmitting Ethernet frames in the 802.1q encapsulation.
C. Configuring an interface with the switchport mode dynamic command will prevent VLAN hopping.
D. An end station attempts to redirect VLAN traffic by transmitting Ethernet frames in the 802.1q encapsulation.
E. Configuring an interface with the "switchport mode access" command will prevent VLAN hopping.
Refer to the exhibit. PCs in VLAN 2 are not able to communicate with PCs in VLAN 3.
What could be the cause？（）
A. IP routing is not enabled.
B. VTP is not configured correctly on the interfaces.
C. The command mls rp management-interface is missing.
D. The command mls rp ip must be disabled to enable the routing.
You are configuring a Cisco multilayer switch for the Company network.
Which command would you use to configure a port to act as a routed interface？（）
A. ip routing
B. switchport mode trunk
C. no switchport
D. switchport trunk native vlan 1
E. None of the other alternatives apply
Which of the following could be used to provide a Layer 3 data path between separate VLANs？（）
A. VLAN trunking
B. An external router
C. An internal route processor
D. VLAN capable bridge
E. EtherChannel
最新試題
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What two things will occur when an edge port receives a BPDU？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which three statements about STP timers are true？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）