Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1？（）
A. Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAs
B. No redistributed routes can appear in Area 1, only summary routes
C. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs
D. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which st atement is true?（）
A. Router RTA is the BDR
B. Router RTA is directly connected to interface 192.168.45.1
C. Neighbor 192.168.45.1 has changed its OSPF priority number
D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs
Refer to the exhibit. Which statement is true about the configuration? （）
A. RTA will not establish an OSPF adjacency w ith RTB
B. RTA will send OSPF hello packets, but will not send OSPF updates
C. RTA will not accept OSPF hello packets from RTB
D. RTA will send OSPF updates, but will not establish an adjacency with RTB
A. Ensure that an interface has been configured with an IP address
B. Ensure that IP classless is enabled
C. Ensure that the interfaces can ping their directly connected neighbors
D. Ensure that an interface has been configured with an IP address and is up
Open Shortes t Path First (OSPF) is a routing protocol developed for Internet Protocol (IP) networks by the Interior Gateway Protocol (IGP) working group of the Internet Engineering Task Force (IETF).
Which two statements best describe the OSPF link - state routing pro tocol?（）
A. OSPF sends updates every 10 seconds
B. OSPF sends triggered updates when a network change occurs
C. When a link state is changed, the router that detected the change creates a link - state advertisement (LSA) and propagates it to all OSPF devices using the 224.0.0.6 multicast address
D. OSPF sends summaries of individual link- state entries every 30 minutes to ensure LSDB synchronization
OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）
A. The ip ospf network broadcast command should be configured on each Frame Relay interface
B. The ip ospf network non -broadcast command should be configured on each Frame Relay interface
C. Th e ip ospf priority value on the spoke routers should be set to 0
D. The ip ospf priority value on the hub router should be set to 0
E. The neighbor command should be configured under the OSPF routing process on all routers
最新試題
Which of the following are true of both OSPFv2 and OSPFv3?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0