A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values.
Which statement is true about how BGP would select the best path?()
A. To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
B. Th e router will prefer the shortest autonomous system path
C. If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
D. The router will prefer the route with the lower MED
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Which two statement s are correct?()
A. All the routes were redistributed into BGP from an IGP
B. All the routes were originated by BGP with the network command
C. All six routes will be installed in the routing table
D. Four routes will be installed in the routing ta ble
E. Two routes will be installed in the routing table
Refer to the exhibit. Which two statements are true about the partial configuration that is provided.()
A. The peer group shortens the EBGP configuration
B. The peer group shortens the IBGP configuration
C. All the configured neighbors are in autonomous system 100
D. Three AS - path filters are applied to each BGP neighbor
E. Only the outgoing filters are applied to BGP updates
A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply
A. Interfaces will automatically detect and build adjacencies with neighbor routers
B. DR and BDR elections will not occur
C. DR and BDR elections will occur
D. The neighbor command is required to build adjacencies
E. All routers must be configured in a fully meshed topology with all other routers
A. Down, Init, 2 - Way, Exstart, Exchange, Loading, and Full
B. Down, Init, 2 - Wa y, Exchange, Exstart, Loading, and Full
C. Down, 2 - Way, Init, Loading, Exstart, Exchange, and Full
D. Down, 2 - Way, Init, Exchange, Exstart, Loading, and Full
E. Down, Init, 2 - Way, Loading, Exstart, Exchange, and Full
F. Down, 2 - Way, Init, Exstart, Exch ange, Loading, and Full
最新試題
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()