A. Only one IPv6 address can be assigned to each interface.
B. IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
C. Each host can a utoconfigure its address without the aid of a DHCP server.
D. Only one IPv6 address is assigned per node.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Autonomous systems 200 and 300 have EBGP sessions established with their directly connected routers in au tonomous system 100. IGP has been configured on all routers in autonomous system 100 and they successfully exchange routing updates. Traffic originated in autonomous system 200 cannot reach the destination autonomous system 300. What configuration shoul d be done on the routers in autonomous system 100 in order for the traffic coming from autonomous system 200 to be forwarded to autonomous system 300?（）
A. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned off.
B. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned on.
C. IBGP session must be established between routers R1 R2 and R2 R3, and the synchronization must be turned on.
D. IBGP session mu st be established between routers R1 and R3, and the synchronization must be turned off.
E. IBGP speakers within autonomous 100 must be fully meshed, and the synchronization must be turned off.
F. IBGP session must be established between routers R1 and R3, and the synchronization must be turned on.
Refer to the exhibit. By default, when RTB passes BGP advertisements from RTA about network 192.168.2.0 to RTC, what address will be listed as the next - hop address? （）
A. 10.1.1.2
B. 192.168.1.49
C. 10.1.1.1
D. 192.168.1.50
Based on the show ip bgp summary output, which two statements are true?（）
A. The BGP session to the 10.3.3.3 neighbor is established, but the router has not received any BGP routing updates from the 10.3.3.3 neighbor.
B. The router is attempting to establish a BGP peering session with the 10.2.2.2 neighbor.
C. The router is attempting to establish a BGP peering session with the 10.1.1.1 neighbor.
D. The BGP session to the 10.3.3.3 neighbor is established.
E. The BGP session to the 10.2.2.2 neighbor is established.
F. The BGP session to the 10.1.1.1 neighbor is established.
A. An internal routing protocol can be used to reach an EBGP neighbor.
B. The next hop does not change when BGP updates are exchanged between EBGP neighbors.
C. EBGP requires a full mesh.
D. A static route can be used to form an adjacency between neighbors.
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router responds with a router advertisement (RA).
Which two items are c ontained in the RA?（）
A. any route advertisements it has received
B. prefixes for the link
C. keepalive timers
D. IPv6 address for the host
E. request for the local host IP address
F. lifetime of the prefix
最新試題
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）