A. There are three IGMP modes: dense mode, sparse mode, and sparse - dense mode
B. IGMP is used to register individual hosts with a multicast group
C. IGMP version 3 enables a multicast receiving host to specify to the router which sources it should forward traffic from
D. IGMP messages a re IP datagrams with a protocol value of 2, destination address of 224.0.0.2, and a TTL value of 1
E. IGMP is a multicast routing protocol that makes packet - forwarding decisions independent of other routing protocols such as EIGRP
F. IGMP snooping ru ns on Layer 3 routers
您可能感興趣的試卷
你可能感興趣的試題
A. PIM sparse - dense
B. Bidir - PIM
C. PIM - RP
D. PIM - DM
E. PIM - SM
A. membership query message
B. membership report message
C. leave group message
D. source filtering
E. destination filtering
A. PIM - DM
B. PIM - SM
C. PIM - RP
D. CGMP
E. IGMP snooping
In IPv6 network, an IPv6 overlay tunnel is required to communicate with isolated IPv6 networks across the existing IPv4 infrastructurE. There are currently fiv e IPv6 overlay tunnel types.
Which three IPv6 overlay tunnel statements are true？（）
A. Overlay tunnels can only be configured between border routers capable of supporting IPv4 and IPv6.
B. An manual overlay tunnel supports point - to - multipo int tunnels capable of carrying IPv6 and Connectionless Network Service (CLNS) packets.
C. Overlay tunneling encapsulates IPv6 packets in IPv4 packets for delivery across an IPv4 infrastructure.
D. Overlay tunnels can be configured between border route rs or between a border router and a host capable of supporting IPv4 and IPv6.
E. Cisco IOS supports manual, generic routing encapsulation (GRE), IPv4 - compatible, 6to4, and Intra - Site Automatic Tunnel Addressing Protocol (ISATAP) overlay tunneling mechan isms.
F. Cisco IOS supports manual, generic routing encapsulation (GRE), IPv6 - compatible, 4to6, and Multiprotocol Label Switching (MPLS) overlay tunneling mechanisms.
A. An automatic 6to4 tunnel does not req uire dual - stack (IPv4 and IPv6) routers at the tunnel endpoints.
B. An automatic 6to4 tunnel allows multiple IPv4 destinations.
C. A manually configured IPv6 in IPv4 tunnel allows multiple IPv4 destinations.
D. A manually configured IPv6 in IPv4 tunnel does not require dual- stack (IPv4 and IPv6) routers at the tunnel endpoints.
最新試題
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）