HSRP is being set up between two Company devices.
In what three states is it possible for an HSRP router to be in？（）
A. Standby
B. Established
C. Active
D. Idle
E. Backup
F. Init
您可能感興趣的試卷
你可能感興趣的試題
R1 and R2 exchange HSRP between each other in the Company network.
In which three HSRP states do routers send hello messages？（）
A. Learn
B. Speak
C. Standby
D. Listen
E. Active
F. Remove
You need to implement a high availability design in the Company routed network.
Which protocol allows for the automatic selection and simultaneous use of multiple available gateways as well as automatic failover between those gateways？（）
A. VRRP
B. GLBP
C. IRDP
D. HSRP
E. None of the other alternatives apply
You need to decide on the best router redundancy protocol to use in the Company network.
Which two statements are true about HSRP， VRRP， and GLBP？（）
A. GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B. HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C. GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D. Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E. GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.
Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）
A. Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B. Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C. Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D. All routers configured for HSRP load balancing must be configured with the same priority.
E. Routers configured for HSRP must belong to only one group per HSRP interface.
You want to implement router redundancy in the Company network using the best method available.
Which protocol specified by RFC 2281 provides network redundancy for IP networks， ensuring that user traffic immediately and transparently recovers from first-hop failures in network edge devices or access circuits？（）
A. ICMP
B. IRDP
C. HSRP
D. STP
E. None of the other alternatives apply
最新試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which router redundancy protocol cannot be configured for interface tracking？（）
What two things will occur when an edge port receives a BPDU？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）