A.enables PortFast
B.disables trunking
C.disables Cisco Discovery Protocol
D.enables port security
E.enables loopguard
F.disables EtherChannel
您可能感興趣的試卷
你可能感興趣的試題
You are implementing basic switch security best practices.
Which of these is a tactic that you can use to mitigate compromises from being launched through the switch？（）
A.Make all ports private VLAN ports.
B.Place all unused ports in native VLAN 1 until needed.
C.Proactively configure unused switch ports as access ports.
D.Disable Cisco Discovery Protocol globally.
Three Cisco Catalyst switches have been configured with a first-hop redundancy protocol. While reviewing some show commands， debug output， and the syslog， you discover the following information：
What conclusion can you infer from this information？（）
A.VRRP is initializing and operating correctly.
B.HSRP is not properly exchanging three hello messages.
C.VRRP is not properly exchanging three hello messages.
D.HSRP is initializing and operating correctly.
E.GLBP is not properly exchanging three hello messages.
F.GLBP is initializing and operating correctly.
You work as a network engineer for . You study the exhibit carefully. Three switches are configured for HSRP. Switch1 remains in the HSRP listen state.
What is the most likely cause of this status？（）
A.this is normal operation
B.IP addressing is incorrect
C.standby group number does not match VLAN number
D.incorrect standby timers
E.incorrect priority commands
hostname Switch1
interface Vlan10
ip address 172.16.10.32 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 130
hostname Switch2
interface Vlan10
ip address 172.16.10.33 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 120
HSRP was implemented and configured on two switches while scheduled network maintenance was performed.
After the two switches have finished rebooting， you notice via show commands that Switch2 is the HSRP active router.
Which two items are most likely the cause of Switch1 not becoming the active router？ （）
A.premption is disabled
B.standby group number does not match VLAN number
C.IP addressing is incorrect
D.IP redirect is disabled
E.incorrect standby timers
F.booting delays
You work as a network engineer for . You study the exhibit carefully. From the configuration shown，
what can be determined？（）
Exhibit:
A.The remaining secure MAC addresses will be dynamically learned， converted to sticky secure MAC addresses， and added to the running configuration.
B.Since a voice VLAN is configured in this example， port security should be set for a maximum of 2.
C.The sticky addresses will only be those manually configured MAC addresses enabled with the sticky keyword.
D.A security violation will restrict the number of addresses to a maximum of 10 addresses per access VLAN and voice VLAN. The port will be shut down if more than 10 devices per VLAN attempt to access the port.
最新試題
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. Which statement is true about the output？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which statement is correct about RSTP port roles？（）
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）