A.Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
B.Enter the no switchport command to disable Layer 2 functionality at the interface level.
C.Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
D.Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.
您可能感興趣的試卷
你可能感興趣的試題
A.ease of IP address assignment versus use of external routers
B.redundancy from trunking between distribution layer switches
C.provides first-hop redundancy to clients
D.allows inter-VLAN communication without requiring complexity of routing protocols
You work as a network engineer for . You study the exhibit carefully.
What best describes the Cisco IOS IP SLA command and output in the exhibit？（）
A.verifies which operation types have been enabled for IP SLA source
B.verifies which operation types have been enabled for IP SLA responder
C.verifies which operation types are supported in software
D.verifies enabled operation types that are not running
You work as a network engineer for. You study the exhibit carefully. Which of these is true based upon the output shown in the command？（）
Exhibit：
A.The port has security enabled and has shut down due to a security violation.
B.The port is operational and has reached its configured maximum allowed number of MAC addresses.
C.The port will allow access for 11 MAC addresses in addition to the 3 configured MAC addresses.
D.If the number of devices attempting to access the port exceeds 11， the port will shut down for 20 minutes， as configured.
A.PACLs can be applied in the inbound or outbound direction of a Layer 2 physical interface.
B.At Layer 2， a MAC address PACL will take precedence over any existing Layer 3 PACL.
C.When you apply a port ACL to a trunk port， the ACL filters traffic on all VLANs present on the trunk port.
D.PACLs are not supported on EtherChannel interfaces.
A.Configure the private VLAN port parameters.
B.Configure and map the secondary VLAN to the primary VLAN.
C.Disable IGMP snooping.
D.Set the VTP mode to transparent.
最新試題
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Which statement is correct about RSTP port roles？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）