You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch,
what can you determine regarding Layer 3 routing functionality of the interface?()
Exhibit:
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
您可能感興趣的試卷
你可能感興趣的試題
A new floor has been added to the enterprise campus network, providing client access for desktop PCs, laptops, and IP phones for employees and guests. During verification, a few desktop PCs have limited corporate access but not Internet access. Most other desktop PCs, all laptops, and IP phones are working correctly. Additional information indicates that the desktop PCs are obtaining IP host addresses from the DHCP server, which is intended for only the IP phones.
Where should troubleshooting about this connectivity issue be focused?()
A.DNS
B.first-hop redundancy protocol
C.DHCP server and options
D.VLAN mapping
E.client network configuration
F.routing protocols
A new building has been added to the enterprise campus network, providing client access for desktop PCs, laptops, and IP phones for employees and guests. During verification, only a few laptops using
wireless are reported to have problems, while other desktops, IP phones, and most other wireless laptops are fully operational. Additional information received about the problem indicates that, while the problematic wireless laptops cannot reach internal corporate websites, they can reach the Internet.
Where should troubleshooting about this connectivity issue be focused?()
A.client network configuration
B.VLAN mapping
C.routing protocols
D.first-hop redundancy protocol
You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown,
what can be determined? ()
Exhibit:
A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters; therefore, it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode, not sub-interface mode, to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have
assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state.
What must be true in an SVI configuration to bring the VLAN and line protocol up?()
A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface, the operational status will always be in an "up/up" state.
A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.
最新試題
What must be the same to make multiple switches part of the same Multiple Spanning Tree (MST)?()
Refer to the exhibit. Initially, LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link?()
If G1/0/1 on DS1 is shutdown, what will be the current priority value of the Vlan105’s group on DS1 ?()
During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()
Which statement is correct about RSTP port roles?()
Refer to the exhibit. Which statement is true about the output?()
Refer to the exhibit. Which Virtual Router Redundancy Protocol (VRRP) statement is true about the roles of the master virtual router and the backup virtual router?()
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1? ()