A. Based on the default timers, OSPF d etects a failure faster than IS - IS does.
B. OSPF default timers permit more tuning than IS - IS does.
C. IS - IS is more efficient than OSPF in the use of CPU resources.
D. OSPF is more scalable than IS - IS because of its ability to identify normal, stub, an d NSSA areas.
E. IS - IS and OSPF are both Open Standard, link - state routing protocols which support VLSM.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. A network administrator has configured DHCP services on the router asshown. DHCP clients connected to the FastEthernet0/0 interface are working properly. DHCP clients connected to the FastEthernet0/1 interface are not receiving addresses.
Which two statements contain recommendations that will solve the problem?（）
A.The network shown in the output under the ip dhcp pool Central command should be changed to network 10.10.0.0 with a mask of 255.255.255.0
B.A second DHCP pool for network 10 .10.0.0/24 should be configured
C.An ip dhcp excluded - address global configuration command for network 10.10.0.0/24 should be issued
D.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/0 c onfiguration
E.The ip helper -address 10.0.0.1 command should be issued so that the address can be added to the Fast Ethernet0/1 configuration
Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:
*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active
*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.
Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.
Which statement best describes the reason for the error messages?（）
A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.
B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.
C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .
A router is running BGP and receives more than one route for a particular prefix. Assume all the routes for this prefix have the same attributes.
Which three path features would be reasons be for the rou ter to ignore some of the routes and not consider them as candidates for the best path?（）
A. paths from an internal BGP (iBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
B. paths for which the NEXT_HOP is inaccess ible
C. paths from an external BGP (eBGP) neighbor if the local autonomous system (AS) appears in the AS_PATH
D. paths for which the NEXT_HOP is accessible
E. paths that are marked as synchronized in the show ip bgp output
F. paths that are marked as not synchronized in the show ip bgp output
You are a network techn ician, study the exhibit carefully. All multilayer switches are running PIM sparse mode. Host CKB and Host CKF are sending IGMPv2 join messages to their respective multilayer switches. Which description is correct?（）
A. Switches 1, 2, 3, and 6 will part icipate in the multicast tree once pruning has taken place.
B. Switches 2 and 6 will participate in the multicast tree once pruning has taken place.
C. Switches 1, 2, 3, and 6 will participate in the multicast tree.
D. The multicast server is the rendez vous point of the multicast tree.
A. IS - IS is capable of supporting IPv4 and IPv6.
B. IS - IS is only capable of supporting IPv4 and CLNS.
C. IS - IS routers use ES - IS hellos (ESH) to establish and to maintain neighbor relationships.
D. IS - IS routers run the Bellman - Ford algorithm against their LSDBs to pick the best paths.
E. Level 1 routers learn about paths within the area of which they are a part.
F. Level 2 routers learn about paths both within areas and between areas.
最新試題
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable