A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface
C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface
D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface
E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?（）
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
Which statement is correct based upon the following output from the show command on RT1 ? （）
A. OSPFv3 establishes neighbor adjacencies by using global IPv6 addresses.
B. OSPFv3 establishes neighbor adjacencies by using Link - local addresses.
C. RT1 owns a subnet mask of 64 bits.
D. OSPFv3 establishes neighbor adjacencies by using IPv4 addr esses.
The following exhibit show s ipv6 route output. What would the metric be for a summary route that summarizes all three OSPFv3 routes displayed?（）
A. 160
B. 140
C. 120
D. 100
A. A generic Hello
B. Point - to - point Level 1, point - to -point Level 2, LAN Level 1, LAN Level 2
C. Point - to - point Level 1, point - to - point Level 2, LAN
D. Point - to - point, LAN Level 1, LAN Level 2
A. The sequence numbers are checked, and if the LSA is val id it is entered into the topology database.
B. The LSA is placed in the topological database and an acknowledgement is sent to the transmitting router.
C. The LSA is dropped and a message is sent to the transmitting router.
D. The LSA is flooded imme diately out of all the OSPF interfaces, except the interface from which the LSA was received.
最新試題
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456