Router R1 has been configured for EIGRP. The configuratio n also includes an ACL with one line -access - list 1 permit 10.100.32.0 0.0.15.255 - and the EIGRP configuration includes the distribute -list 1 in command.
Which of the following routes could not be displayed in the output of the show ip eigrp topology comm and as a result?（）
A. 10.10.32.0/19
B. 10.10.44.0/22
C. 10.10.40.96/27
D. 10.10.48.0/23
E. 10.10.60.0/30
您可能感興趣的試卷
你可能感興趣的試題
Router R1 lists 4 routes for subnet 10.1.1.0/24 in the output of the show ip eigrp topology all - links command. The variance 200 command is configured, but no other related commands are configured. Which of the following rules are true regarding R1's decision of what r outes to add to the IP routing table?
Note that RD refers to reported distance and FD to feasible distanc E.（）
A. Adds all routes for which the metric is <= 200 * the best metric among all routes
B. Adds all routes because of the ridiculously high variance setting
C. Adds all successor and feasible successor routes
D. Adds all successor and feasible successor routes for which the metric is<=200 * the best metric among all routes
A network design shows that R1 has four different possible paths from itself to the Data Center subnets.
Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）
A. show ip eigrp topology
B. show ip eigrp topology all - links
C. show ip route eigrp
D. show ip route eigrp all - links
E. show ip eigrp topology all - learned
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of the 100 branch routers.
Which of the following could be true about the number of EIGRP neighbor ships?（）
A. A partial mesh totaling 100: one between the central - site router and each of the 100 branches.
B. A full mesh - (101 * 100) / 2 = 5050 - One neighborship between each pair of routers.
C. 101 - One between each router (including the central site) a nd its nearby PE router.
D. None of the answers is correct.
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? （）
A. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
B. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP a ddress 10.0.0.1
D. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
E. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
A. BOOTP
B. TFTP
C. ARP
D. DNS
E. proxy - ARP
F. FTP
最新試題
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable