A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
您可能感興趣的試卷
你可能感興趣的試題
A.five
B.three
C.six
D.four
A.cisco-leap，eap-fast，eap-peap（gtc），eap-tls
B.cisco-leap，eap-psk，eap-peap（ms-chap v2），eap-tls
C.cisco-leap，eap-fast，eap-peap（ms-chap v2），eap-ttls
D.cisco-leap，eap-md5，eap-peap（gtc），eap-ttls
You are using standalone cisco aironet 1400 series wireless bridges for a nine-mile point-to-point wireless link between two buildings.
Which distance setting should you use for the bridge configured as the root？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
When configuring a cisco 3845 integrated services router to support 802.11b and g clients.
Which of the following commands would be correct？（）
A.router（config-if）# speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
B.router（config-if）# speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 basic-18.0 24.0 36.0 48.0 54.0
C.router（config-if）# speed basic-1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
D.router（config-if）# speed 1.0 2.0 5.5 basic-6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
A.enable concatenation on the non-root bridge only
B.enable concatenation on the root bridge only
C.enable concatenation on both the root bridge and non-root bridge
D.enable concatenation on the root bridge and set it as desirable on the non-root bridge
E.set concatenation as desirable on the root bridge and enable it on the non-root bridge
最新試題
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）