On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card is not associated to the network.
B.The client card has awakened from power-save mode.
C.The driver has been installed incorrectly.
D.The client card has failed.
您可能感興趣的試卷
你可能感興趣的試題
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved forthe Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select ontheWLAN controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.
You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct theproblem？（）
A.ensure channels are deployed such that they do not overlap
B.allow for the automatic containment of rogue access points
C.ensure each area is covered by a minimum of three access points
D.ensure a minimum RSSI value of -50
A.4
B.32
C.8
D.16
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch.
How would you interconnect and configure LAG for connectivity and ensure redundancy？（）
A.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channelgroup.
B.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and CiscoWLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
C.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
D.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and CiscoWLC ports 3 and 4 to Catalyst gigabit module slot 2 channel group 40.
A.50 feet [15 meters]
B.200 feet [60 meters]
C.150 feet [45 meters]
D.100 feet [30 meters]
最新試題
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）