A.Ongoing Support Handoff Meeting
B.Staff Training
C.Detailed Design Development
D.Staging and System Migration
您可能感興趣的試卷
你可能感興趣的試題
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） isfailing， but association using EAP-PEAP is functioning.
What needs to be enabled on the standalone accesspoint to correct this issue？（）
A.network EAP
B.open authentication plus MAC
C.open authentication plus EAP
D.a shared key
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode.When you set the link back to operational mode you loose association to the root bridge.
Which action will correct the problem？（）
A.Configure the bridge to force infrastructure devices to associate only to the SSID parameter.
B.Enable passwords on both bridges.
C.Configure the distance parameter value.
D.Configure the proper channel.
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on astandalone WLAN.
What may have caused this problem？（）
A.The minimum data rate is not set to 11 Mbps.
B.Publicly Secure Packet forwarding is enabled.
C.The access point is set to the least congested channel.
D.An address resolution protocol has been disabled.
On a Cisco Aironet 1130AG Series standalone access point， the status LED is dark blue andblinking.
What does this indicate？（）
A.The internal radio has failed.
B.A firmware upgrade is in progress.
C.An access point buffer overflow is occurring.
D.The access point is booting.
In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attemptsreport on the Cisco Secure ACS，you find this error："Unknown network access server NAS."
Which problemmayhave caused this failure？（）
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
最新試題
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）