A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch.
How would younterconnect and configure LAG for connectivity and ensure redundancy？（）
A.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channel group.
B.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
C.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 40.
D.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
您可能感興趣的試卷
你可能感興趣的試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client that isanchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run a debug command on the 4402 controller.
Which message would best describe the establishment of the tunnel fromthe foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Received Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Received Plumbing duplex mobility tunnel message
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication.
In order toaccomplish this，which two IETF RADIUS attributes should you configure on the Cisco Secure ACS？（）
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
You have been called upon to add location-based services into an existing controller-based wireless designwhich primarily encompasses handheld devices such as barcode scanners and Cisco 7920 wireless IPphones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference？（）
A.sniffer mode
B.monitor mode
C.location mode
D.tracking mode
A.Monitor
B.Rogue Detector
C.Sniffer
D.Mirror
A.RTS threshold = 4000， CWmin = 3
B.RTS threshold = 1， CWmin = 4
C.RTS threshold = 4000， CWmin = 5
D.RTS threshold = 1， CWmin = 5
最新試題
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
Which of the following commands on the wireless interface of a Cisco 3845 Integrated Service Router allows the SSID to broadcast？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）