A.15
B.10
C.1
D.5
您可能感興趣的試卷
你可能感興趣的試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients. In addition to implementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actions should you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication.
Inorder to accomplish this， which two IETF RADIUS attributes should you configure on the Cisco Secure ACS？（）
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.
What does this indicate？（）
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
A.8 feet [2.4 meters]
B.16 feet [4.8 meters]
C.24 feet [7.3 meters]
D.40 feet [12.1 meters]
最新試題
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）