Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled？（）
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
您可能感興趣的試卷
你可能感興趣的試題
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-pointwireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as theroot？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID beacon rate is 10 seconds and you have discovered an issue with the RFID timeout value.
Where and how should the RFID value be changed？（）
A.on the Cisco WCS， to 95 seconds
B.on the wireless controller， to 45 seconds
C.on the wireless controller， to 95 seconds
D.on the Cisco WCS， to 45 seconds
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.
What does this indicate about the access point？（）
A.duplicate IP address
B.code upgrade in progress
C.normal operation
D.searching for primary controller
最新試題
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）