Refer to the exhibit. On the basis of the configuration that is provided, how would the BGP updates that come from router R1 be replicated inside autonomous system 65200？（）
A. All BGP updates that are received on router R 2 will be sent to routers R3 and R4. Routers R3 and R4 will then forward those BGP updates to router R5
B. None of the BGP updates that are received on router R2 will ever be received by router R5
C. All BGP updates that are received on router R2 will not be sent to routers R3 and R4
D. All BGP updates that are received on router R2 will be sent directly to router R5
您可能感興趣的試卷
你可能感興趣的試題
A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
A router has two paths to reach another network in a different autonomous system. Neither route was generated by the local router and both routes have the same default weight an d local preference values.
Which statement is true about how BGP would select the best path?（）
A. To influence one route to be preferred, its default local preference value will be changed via the use of the command bgp default local - preference 50
B. Th e router will prefer the shortest autonomous system path
C. If the command bgp always - compare - med has been given, then the router will prefer the route with the highest MED
D. The router will prefer the route with the lower MED
Refer to the exhibit. Which two statement s are correct?（）
A. All the routes were redistributed into BGP from an IGP
B. All the routes were originated by BGP with the network command
C. All six routes will be installed in the routing table
D. Four routes will be installed in the routing ta ble
E. Two routes will be installed in the routing table
Refer to the exhibit. Which two statements are true about the partial configuration that is provided.（）
A. The peer group shortens the EBGP configuration
B. The peer group shortens the IBGP configuration
C. All the configured neighbors are in autonomous system 100
D. Three AS - path filters are applied to each BGP neighbor
E. Only the outgoing filters are applied to BGP updates
A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply
最新試題
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following answers lists a multicast IPv6 address?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）