A.isolated
B.protected
C.private
D.associated
E.promiscuous
F.munity
您可能感興趣的試卷
你可能感興趣的試題
A.enables PortFast
B.disables trunking
C.disables Cisco Discovery Protocol
D.enables port security
E.enables loopguard
F.disables EtherChannel
You are implementing basic switch security best practices.
Which of these is a tactic that you can use to mitigate compromises from being launched through the switch？（）
A.Make all ports private VLAN ports.
B.Place all unused ports in native VLAN 1 until needed.
C.Proactively configure unused switch ports as access ports.
D.Disable Cisco Discovery Protocol globally.
Three Cisco Catalyst switches have been configured with a first-hop redundancy protocol. While reviewing some show commands， debug output， and the syslog， you discover the following information：
What conclusion can you infer from this information？（）
A.VRRP is initializing and operating correctly.
B.HSRP is not properly exchanging three hello messages.
C.VRRP is not properly exchanging three hello messages.
D.HSRP is initializing and operating correctly.
E.GLBP is not properly exchanging three hello messages.
F.GLBP is initializing and operating correctly.
You work as a network engineer for . You study the exhibit carefully. Three switches are configured for HSRP. Switch1 remains in the HSRP listen state.
What is the most likely cause of this status？（）
A.this is normal operation
B.IP addressing is incorrect
C.standby group number does not match VLAN number
D.incorrect standby timers
E.incorrect priority commands
hostname Switch1
interface Vlan10
ip address 172.16.10.32 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 130
hostname Switch2
interface Vlan10
ip address 172.16.10.33 255.255.255.0
no ip redirects
standby 1 ip 172.16.10.110
standby 1 timers 1 5
standby 1 priority 120
HSRP was implemented and configured on two switches while scheduled network maintenance was performed.
After the two switches have finished rebooting， you notice via show commands that Switch2 is the HSRP active router.
Which two items are most likely the cause of Switch1 not becoming the active router？ （）
A.premption is disabled
B.standby group number does not match VLAN number
C.IP addressing is incorrect
D.IP redirect is disabled
E.incorrect standby timers
F.booting delays
最新試題
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which two statements about the various implementations of STP are true？（）
Which three statements about STP timers are true？（）